Vertex standard programming software download
- VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD PDF
- VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD MANUAL
- VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD SERIES
They may not be both the same if you have a radio 'repeater' your input frequency could be 5MHz higher than your receive frequency.Īnd last- you need to know if your system has a 'PL' tone (CTCSS, or DCS) subaudible tone that will break the squelch. Next, find out the exact transmit and receive frequencies for your radio. Ok, is your work radio an analog radio? Is it narrowband FM? Is it digital MOTOTRBO? First of all, technically, you can't use this radio to talk to anyone other than ham radio- that being said, if you want to proceed at your own risk. If you have checked all your wiring AND the power connections, it is less likely a programming error. Get thick wire or the harness may not provide enough amps and it will get really, really hot! The wiring harness from Vertex is the best one. This occurs often when the wire is too thin for the amperage required. You did not mention if this is a 25 or 50 watt radio. The radio requires a steady 12 VDC input, or in a vehicle, 13.2 VDC. External Speaker mute on: Level High External Speaker mute off: Open Pin 25: E Chassis ground.
VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD PDF
Descargar Una Noche De Verano Gerri Hill Pdf there. This status can be changed by CE49 programmer. A Signal is present (Squelch is open): Level High No Signal is present (Squelch is closed): Open When you connect the solder jumper on JP2002, this port changes to PULL UP (5 V) output. None/A PORT/B PORT/C PORT/D PORT/E PORT/HA PORT Pin 23: EXT SQL Open collector output. If the HA feature is assigned to these ports, a cur- rent amplifier must be connected between the Horn circuit and the port. The possible programming features (use CE49) are illustrated below. The logic output appears at these pins when the front panel's PF key is turned on. Pin 18: E Ground for all logic levels and power supply re- turn. If the jumper setting is 'HI-speed Data' (JP2003 jumpered), this port is usable for 9600 bps DATA communications, because the filter and limiter are not engaged in the Audio line. Output level 200 mV/600 Ohms If the Jumper setting is 'Low-speed Data' (JP2004 jumpered), this port is usable in the AUDIO (300~3000 Hz) range. Output level 600 mV/10k Ohms RX Low-speed Data Output Type (jumper JP2004).
VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD MANUAL
Ignition 13.8V Pin 16: NC A IN CCESSORY DSUB 25-Pin Operating Manual Reprint C ONNECTOR Pin 17: RX DO RX Hi-speed Data Output Type (jumper JP2003). This feature is only enabled on transceivers con- figured for Dual Deck operation. Via programming by your VERTEX STANDARD dealer.
VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD SERIES
View and Download Vertex Standard VX-3200 Series operating manual online. Maximum current is 20 mA.Ĭurrent list of Vertex/Standard Radio programming files available for download in the members area. Maximum output current is 200 mA Pin 15: IGN The VX-5500 may automatically be switched to the STAND-BY mode when the vehicle's igni-tion key is turned on. Switched and regulated DC 5.0V output for supplying power to an accessory (jumper JP2007). Pin 14: DC OUT Switched 13.8V output for supplying power to an accessory (jumper JP2008). If the jumper setting is 'HI-speed Data' (JP2005 jumpered), this port is usable for 9600 bps DATA communications, because the filter and limiter are not engaged in the Audio line. Input level 40 mV/600-Ohms If the Jumper setting is 'Low-speed Data' (JP2006 jumpered), this port is usable in the AUDIO (300~3000 Hz) range. Input level 800 mV/600 Ohms, Max.input 1.2V Tx Low-speed Data input Type ( Jumper JP2006). DSUB 25-P Pin 13: TXDI TX Hi-speed Data Input Type (jumper JP2005). I found this info at: It's easier to read it there.